Sputtered Ir–Ru based catalysts for oxygen evolution reaction: Study of iridium effect on stability

Magnetron sputtered low-loading iridium-ruthenium thin films are investigated as catalysts for the Oxygen Evolution Reaction at the anode of the Proton Exchange Membrane Water Electrolyzer. Electrochemical performance of 50 nm thin catalysts (Ir pure, Ir–Ru 1:1, Ir–Ru 1:3, Ru pure) is tested in a Rotating Disk Electrode. Corresponding Tafel slopes are measured before and after the CV-based procedure to compare the activity and stability of prepared compounds. Calculated activities prior to the procedure confirm higher activity of ruthenium-containing catalysts (Ru pure > Ir–Ru 1:3 > Ir–Ru 1:1 > Ir pure). However, after the procedure a higher activity and less degradation of Ir–Ru 1:3 is observed, compared to Ir–Ru 1:1, i.e. the sample with a higher amount of unstable ruthenium performs better. This contradicts the expected behavior of the catalyst. The comprehensive chemical and structural analysis unravels that the stability of Ir–Ru 1:3 sample is connected to RuO₂ chemical state and hcp structure. Obtained results are confirmed by measuring current densities in a single cell.     

Sulfur doped biocarbon obtained from Sargassum spp. for the oxygen reduction reaction

Sulfured doped carbon electrocatalysts is synthesized from the waste biomass Sargassum spp. Two doping procedures are examined to determine which is better for Oxygen Reduction Reaction (ORR); one by doping biocarbon obtained from the pyrolysis of the biomass and the second through a process of in situ doping in autoclave. The electrocatalyst are obtained from pyrolysis of the sample at 700 °C, which is finally characterized as a metal free electrocatalyst for the ORR. The electrocatalyst are characterized by BET surface area analysis, Raman spectroscopy, X-ray Photoelectron Spectroscopy (XPS) and the electrochemical characterization is determined in 0.1 M KOH. The sample SSKPT-1 exhibits a promising electrocatalytic activity with an onset potential of 0.896 V vs RHE and a current density of 5 mA cm^?2 (at 0.2 V vs. RHE) which could be partly attributed to its high BET surface area of 2755 m² g^?1.     

Swapping catalytic active sites from cationic Ni to anionic F in Fe–F–Ni3S2 enables more efficient alkaline oxygen evolution reaction and urea oxidation reaction

Electrolysis of water for producing hydrogen instead of traditional fossil fuels is one of the most promising methods to alleviate environmental pollution and energy crisis. In this work, Fe and F ion co-doped Ni₃S₂ nanoarrays grown on Ni foam substrate were prepared by typical hydrothermal and sulfuration processes for the first time. Density functional theory (DFT) calculation demonstrate that the adsorption energy of the material to water is greatly enhanced due to the doping of F and Fe, which is conducive to the formation of intermediate species and the improvement of electrochemical performance of the electrode. The adsorption energy of anions (F and S) and cations (Fe and Ni) to water in each material was also calculated, and the results showed that F ion showed the most optimal adsorption energy of water, which proved that the doping of F and Fe was beneficial to improve the electrochemical performance of the electrode. It is worth noting that the surface of Fe–F–Ni₃S₂ material will undergo reconstruction during the process of water oxidation reaction and urea oxidation reaction, and amorphous oxides or hydroxides in situ would be formed on the surface of electrode, which are the real active species.     

Enhanced oxygen evolution reaction kinetics through biochar-based nickel-iron phosphides nanocages in water electrolysis for hydrogen production

Highly-efficient and stable non-noble metal electrocatalysts for overcoming the sluggish kinetics of oxygen evolution reaction (OER) is urgent for water electrolysis. Biomass-derived biochar has been considered as promising carbon material because of its advantages such as low-cost, renewable, simple preparation, rich structure, and easy to obtain heteroatom by in-situ doping. Herein, Ni₂P–Fe₂P bimetallic phosphide spherical nanocages encapsulated in N/P-doped pine needles biochar is prepared via a simple two-step pyrolysis method. Benefiting from the maximum synergistic effects of bimetallic phosphide and biochar, high conductivity of biochar encapsulation, highly exposed active sites of Ni₂P–Fe₂P spherical nanocages, rapid mass transfer in porous channels with large specific surface area, and the promotion in adsorption of reaction intermediates by high-level heteroatom doping, the (Ni_0.75Fe_0.25)₂P@NP/C demonstrates excellent OER activity with an overpotential of 250 mV and a Tafel slope of 48 mV/dec at 10 mA/cm² in 1 M KOH. Also it exhibits a long-term durability in 10 h electrolysis and its activity even improves during the electrocatalytic process. The present work provides a favorable strategy for the inexpensive synthesis of biochar-based transition metal electrocatalysts toward OER, and improves the water electrolysis for hydrogen production.     

Enhancing sustainable bioelectricity generation using facile synthesis of nanostructures of bimetallic Co–Ni at the combined support of halloysite nanotubes and reduced graphene oxide as novel oxygen reduction reaction electrocatalyst in single-chambered microbial fuel cells

The present study aims to utilize the high surface area of the nanotube structure of halloysite (HNTs), an aluminosilicate clay, and conductivity of reduced graphene oxide (rGO) as support material for the deposition of nickel (Ni) and cobalt (Co) nanoparticles. With that aim, a novel bimetallic cathode electrocatalyst, Co–Ni @ HNTs-rGO (Catalyst H₃), is developed. This catalyst is characterized by X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and Transmission Electron Microscopy (TEM). Catalyst H₃ demonstrates outstanding oxygen reduction reaction (ORR) activity, electrochemical stability, electrocatalytic performance, and lowest resistance in comparison to the other developed catalysts and conventional Pt/C. Catalyst H₃ is used in single-chambered MFCs (microbial fuel cells), where the anode is filled with molasses-laden wastewater. The attained maximum power density in MFC (catalyst H₃) is 455 ± 9 mW/m², which is higher than other catalysts. All the results indicate towards its potential use in MFC application.     

ZIF-8 derived bimetallic Fe–Ni-Nanoporous carbon for enhanced oxygen reduction reaction

The development of highly efficient nοn-nοble meta? catalysts for (ОRR) in PEMFCs is at the heart of the research, yet their performance is not satisfactory. The Fe–N active sites enclosed in carbon matrix are generally agreed to be the most promising active sites for ORR. In view of this, further effort is made to increase the Fe–N active sites. Here we present the fabrication of novel FeNi bimetallic electrоcatalyst obtained from ZIF, which consists of FeNi nanоallоys incorporated in N-doped carbon (FeNi-NC) featuring carbon nanotubes and porous carbon demonstrates outstanding results for ОRR. The Fe–N and Ni–N active sites synergistically enhance the ORR activity of FeNi-NC catalyst. The FeNi-NC showed remarkable performance in KОH with the half-wave and onset potential of 0.89 V and 0.99 V vs RHE, respectively. This catalyst shows exceptional stability in methanol equivalent to Pt/C commercial. The FeNi-NC retained 71%, while Pt/C commercial retained only 59% of its original current density. The exceptional stability and activity might be associated with the interplay among FeNi active sites and N-doped carbon, the distinct nanо-structure made up of porous carbon and carbon nanotubes with a high graphitization degree.     

Hydrangea like composite catalysts of ultrathin Mo2S3 nanosheets assembled on N,S-dual-doped graphitic biocarbon spheres with highly electrocatalytic activity for HER

Water electrolysis is the most clean and high-efficiency technology for production of hydrogen, an ultimate clean energy in future. Highly efficient non-noble electrocatalysts for hydrogen evolution reaction (HER) are desirable for large scale production of hydrogen by water electrolysis. Especially, exposing as many active sites as possible is a vital way to improve activities of the catalysts. Herein, a series of new hydrangea like composite catalysts of ultrathin Mo₂S₃ nanosheets assembled uprightly and interlacedly on N, S-dual-doped graphitic biocarbon spheres were facilely prepared. The unique structure endowed the catalysts highly exposed edge active sites and prominently high activities for HER. Especially, the optimized catalyst Mo₂S₃/NSCS-50 exhibited as low as 106 mV of overpotential at 10 mA/cm² (denoted as ?₁₀). The catalyst also showed low Tafel slope of 53 mV/dec, low electron transfer resistance of 34 Ω and high stability evidenced by the result that the current density only attenuated 11.7% after 10 h i-t test. The catalyst has shown broad prospect for commercial application in water electrolysis.     

Layered double (Ni,Fe) hydroxide grown on nickel foam and modified by nickel carbonyl powder and carbon black as an efficient electrode for water splitting

Developing novel oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) catalysts is vital for water splitting. Here, carbon black (CB) and nickel carbonyl powder (NCP) are used as components, and the nonionic surfactant polyvinyl pyrrolidone (PVP) is used as a shape-controlled capping agent to easily prepare layered double (Ni, Fe) hydroxide (NiFe-LDH) electrodes. Scanning electron microscopy observation and X-ray photoelectron spectra analysis show that the Fe²⁺-doped layered double hydroxide is grown in situ on nickel foam (NF). CB (XC-72) and NCP further improve the electrical conductivity. At 10 mA?cm^?2, the overpotentials of the OER and HER are 203 mV and 83 mV, respectively, in 1 M KOH. Only 1.48 V is needed when both electrodes are applied for water splitting, and it has a stability of more than 100 h. This work can be used as a medium to elevate the OER and HER performance of NiFe-LDH-based catalysts.     

C-O-Co bond-stabilized CoP on carbon cloth toward hydrogen evolution reaction

Highly active, low-cost, and durable electrocatalysts toward hydrogen evolution reaction (HER) are crucial for electrochemical water splitting. Herein, a green, facial, and effective strategy was proposed to develop CoP on carbon cloth (CoP/o-CC) as efficient self-supported hydrogen evolution electrodes. The designed CoP/o-CC exhibits superior catalytic activity with overpotentials of 118 mV and 95.45 mV to deliver a current density of 10 mA cm^?2 in acidic and alkaline solution, respectively, which is superior to most reported studies. In addition, the designed CoP/o-CC electrode also possesses excellent stability even under a large current density of 100 mA cm^?2. The origin of significantly enhanced stability thereby was further systematically investigated. Experimental study reveals that the oxygenated functional groups on carbon cloth play the role to bind the CoP electrocatalysts, forming C-O-Co bonds. Thus, the enhanced electrochemical and structural stability of CoP/o-CC is predominantly caused by the interfacial interaction of the C-O-Co bonds between the CoP active materials and surface oxygenated functional groups of carbon fiber. Therefore, we believe that this work provides an in-depth insight into the role of interfacial interaction between the substrate and the catalysts and offers a new methodology to design durable and efficient electrocatalysts.     

Hydrogen-rich gas generation via the exhaust gas-fuel reformer for the marine LNG engine

Reformed exhaust gas recirculation technology has attracted great attention in internal combustion engines. A platform of an exhaust gas-fuel reformer connected with the marine LNG engine was set up for generating on-board hydrogen. Based on the platform, effects of the methane to oxygen ratio (M/O) and reformed exhaust gas ratio (R_EG) from the reformer and excess air ratio (λ) from the engine on the components, hydrogen yield, thermal efficiency and reforming process of the reformer were experimentally investigated. Results shown that hydrogen-rich gases (reformate) can be generated by reforming the mixture of engine exhaust gas (about 400 °C) and methane supplied via the reformer with Ni/Al₂O₃ catalyst, and the hydrogen concentration of reformate was between 6.2% and 12.6% by volume. The methane supplied rate and λ affected the components and temperature of the reactant in the reformer, while R_EG changed the gas hour space velocity during the exhaust gas-fuel reforming processes, resulting in the difference in the components of the reformate and thermal efficiency. At the present experimental condition, the highest H₂ concentration reformate was generated under the M/O of 2.0, λ of 1.55 and R_EG of 6%.